APC Smart-UPS Uninterruptible Power Supply 120 VAC User’s Manual 990-7016B, Revision 3 Initial Start-Up To obtain warranty coverage, please fill out and return the warranty registration card now. Inspection Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose. For installation information, see the user manual provided with the Network Management Card (NMC). The user manual is also available on the APC Web site at www.apc.com. External Battery Pack For installation information, see the Smart-UPS X-Series External Battery Pack Installation guide that is included with the external battery pack. User Manual English APC Smart-UPS® 1000/1500 VA 100/120/230 VAC 750/1000XL VA 120/230 VAC Tower Uninterruptible Power Supply. 1 Introduction American Power Conversion Corporation (APC) is the leading national and international manufac-turer of state-of-the-art uninterruptible power supplies, redundant switches, power management soft. For UPS installation information, see the Smart-UPS Quick-Start Guide 750/1000/1500/ 2200/3000 VA 120/230 Vac Tower that is included with the UPS. The guide is also available on the enclosed CD and the APC Web site at www.apc.com. Network Management Card For installation information, see the user manual provided with the Network Management Card.
Advertising
0017
0017
0017
0017
0017
CONNECT TVSS
Back-UPS
®
RS/XS 1200
User’s Manual
1
®
CONTENTS
RJ-45
USB
RJ-11
RJ-11
2
3
CONNECT BATTERY CARTRIDGE
OPERATING ENVIRONMENT
3
4
CONNECT EQUIPMENT / POWER
Monitor
Printer or Scanner
FAX
External Disk or
CD / DVD Drive
Input: 120V~
12A, 60Hz
Circuit Breaker
Push to Reset
SURGE ONLY
BATTERY BACKUP
Computer
5
CHECK BUILDING WIRING
FAULT INDICATOR
Building
Wiring Fault
Wall
Outlet
Modem/
Phone/Fax
TVSS GND
Building Wiring
Fault Indicator
6
Phone Jack
Computer
Modem Port
CONNECT PHONE/MODEM/FAX
TVSS GND
Wall
Outlet
Wall
Outlet
Modem/
Phone/Fax
7
CONNECT 10/100 Base-T or VOIP
Network Jack
Computer
Network Port
8
To Computer USB
Port
CONNECT INTERFACE
Data Port
BR24BP Battery Pack
Computer
11
INSTALL SOFTWARE ON
COMPUTER
There are four status indicators (lights) on the front
panel of the Back-UPS (On Line, On Battery, Overload, and Replace Battery).
On Line (green)
- is lit whenever utility power is
powering the Battery Backup outlets.
On Battery (yellow)
- is lit whenever the battery of
the Back-UPS is powering equipment connected to the
Battery Backup Outlets.
Four Beeps Every 30 Seconds - this alarm is
sounded whenever the Back-UPS is running On Battery. Consider saving work in progress.
Overload (red)
- is lit whenever power demand has
exceeded the capacity of the Back-UPS.
Continuous Tone - this alarm is sounded
whenever the Battery Backup outlets are overloaded.
Circuit Breaker - the circuit breaker button
located on the rear panel of the Back-UPS will stick out if an overload condition forces the Back- UPS to disconnect itself from utility power. If the button sticks out, disconnect non-essential equipment. Reset the circuit breaker by pushing the button inward.
Replace Battery (red)
- is lit whenever the battery is
near the end of its useful life, or if the battery is not con-
nected (see above). A battery that is near the end of its use- ful life has insufficient run-time and should be replaced.
Chirps for 1 Minute Every 5 Hours - this
alarm is sounded whenever the battery has failed the automatic diagnostic test.
Note: Allow the Back-UPS to charge for a full
eight (8) hours prior to use.
Press the front panel Power ON/OFF switch and
observe that the following events occur after pressing and releasing the switch:
• The green On Line indicator flashes.
• The yellow On Battery indicator lights while
a Self-Test is being performed.
• When Self-Test has successfully completed,
![]()
only the green On Line indicator will be lit.
• If the internal battery cartridge is not
connected (see Step 2 above), the green On
Line indicator and red Replace Battery indicators will light. The Back-UPS will also emit a chirping sound.
Continuous Beeping - this alarm is sounded
whenever a low battery condition is reached. Battery run-time is very low. Promptly save any work in progress and exit all open applications. Shutdown the operating system, computer and the Back-UPS.
If Autoplay is not enabled on the computer, proceed
as follows:
1. On the computer desktop of the display, double-
click on My Computer.
2. Double-click on the CD-ROM drive icon and
follow the on-screen instructions.
If the rear panel Building Wiring Fault (red)
indicator is lit, a potential shock hazard exists due to one of the following conditions: • Open or high resistance ground • Hot or neutral polarity reversed • Overloaded neutral circuit Improper building wiring should be corrected by a qualified electrician. Do not use the Back-UPS until the condition that caused the fault is corrected. Note: Improper building wiring will not prevent the Back-UPS from operating, but it will limit its protection capability.
9
SWITCH ON THE BACK-UPS
10
ORIENTATION
12
GROUND
The Back-UPS features a transient
voltage surge-suppression (TVSS) screw for connecting the ground lead on additional surge suppression devices such as network and data line surge protectors.
Wall
Outlet
Modem/
Phone/Fax
TVSS GND
From Data Line
TVSS
Follow the
on-screen
instructions.
On Line
On Battery
Overload
Replace Battery
w
w
w.apc.com
®
RJ-45
USB
10/100 Base-T
VOIP
STATUS INDICATORS AND ALARMS
For connection of APC’s optional
external 24-volt battery pack
(BR24BP) to the Back-UPS RS/XS 1500.
(Back-UPS RS models only)
CABLE
32 - 104
o
F (0 - 40
o
C)
Smart Ups Apc 1500 Manual
001b
0017
0017
0017
Back-UPS
®
RS/XS 1500
Advertising
Popular Brands
Popular manuals
Summary of the content on the page No. 1
™
Installation Guide Smart-UPS X 750/1000/1500 VA Rack-Mount 2U Important Safety Messages Read the instructions carefully to become familiar with the equipment before trying to install, operate, service or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of this symbol to a Caution product safety label indicates that a hazard e Summary of the content on the page No. 2
Inventory All models (4) (1) (1) (1) (1) (4) (1) (2) (2) (1 pair) (2) (4) Rack-Mount brackets 230 Vac models 750/1000 VA models 1500 VA models (2) (2) (2) (4) (1 pair) Models with preinstalled network cards 2 Installation Smart-UPS X 750/1000/1500 VA 120/230 Vac Rack-Mount 2U gen0744a su0434a
Summary of the content on the page No. 3
su0336a Installation Connect the battery Tower to rack-mount conversion 750/1000 VA Rack-mount to tower conversion 1500 VA 12 3 Two post rack Front mount installation 750/1000 VA 1 2 3 Installation Smart-UPS X 750/1000/1500 VA 120/230 Vac Rack-Mount 2U 3 su0322a su0331a su0320a su0324a su0356a su00335a su0337a su0332
Summary of the content on the page No. 4Apc Smart Ups 1500 Xlm Manual
Center mount 750/1000/1500 VA 12 Four post rack installation 1500 VA Use the APC Four Post Rail Kit (included with 1500 VA models only.) 12 Install the bezel and rotate the logo 4 Installation Smart-UPS X 750/1000/1500 VA 120/230 Vac Rack-Mount 2U su0357a su0321a su0440a su0323a su0442a
Apc Smart-ups 1500 User Manual PdfSummary of the content on the page No. 5
Start Up and Configuration Overview 120 Vac SmartSlot 1 External battery pack connector 2 Outlets 3 EPO connector 4 USB port 5 Serial port 6 Chassis ground screw 7 UPS input 8 230 Vac Circuit breaker 9 Controllable outlet groups The outlets on the UPS are configured into groups. To configure the controlled outlet features, navigate to: Main Menu > Control > Outlet1 Control. SKU Controllable Outlet Group 1 750 VA 1000 VA 1 & 2 1500 VA 1, 2, & 3 230 V 1500 VA 120 V 1500 VA Examples of switch
Apc Back Ups 1500 ManualSummary of the content on the page No. 6Apc Smart-ups 1500 Lcd Manual
Electrical connections CAUTION RISK OF EQUIPMENT DAMAGE • Adhere to all local and national electrical codes. • Wiring should be performed by qualified electrician. • Always connect the UPS to a grounded outlet. Failure to follow these instructions can result in equipment damage Display Interface Online LED 1 UPS ON/OFF key 2 On Battery LED 3 Site Wiring Fault LED 4 Replace Battery LED 5 Display interface 6 UP/DOWN arrow keys 7 ENTER key 8 APC by Schneider ESC key 9 Electric su0343a ® Select mod
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2020
Categories |